Use windows xp wireless access point

It is recommended to enable encryption on your wireless accesspoint before your wireless network adapters. Please establishwireless connectivity before enabling encryption. Note: Your network will slow down and wirelesssignal may degrade when enabling encryption due to the addedoverhead. Step 1 Right-click on the computer monitor icon inthe system tray, select View Available WirelessNetworks. The Network Key field will then become available. Step 3 Click on the connect button.

Click the Security tab, click Advanced , and then configure the following:. To configure advanced When the advanced Because of this, you do not need to change the defaults unless you have a specific reason for doing so. The remaining default values in Single Sign On are sufficient for typical wireless deployments. In Fast Roaming , if your wireless AP is configured for pre-authentication, select This network uses pre-authentication.

Click OK to return to the Security tab. In Select the security methods for this network , in Authentication , select WPA2-Enterprise if it is supported by your wireless AP and wireless client network adapters. Otherwise, select WPA-Enterprise. If you are using access points and wireless network adapters that support Otherwise, select TKIP. The settings for both Authentication and Encryption must match the settings configured on your wireless APs. The default settings for Authentication Mode , Max Authentication Failures , and Cache user information for subsequent connections to this network are sufficient for typical wireless deployments.

This setting limits the root CAs that clients trust to the selected CAs. Click Configure. To specify that user identity is masked in phase one of authentication, select Enable Identity Privacy , and in the textbox, type an anonymous identity name, or leave the textbox blank. If you want to create additional profiles, click Add , and then repeat the previous steps, making different choices to customize each profile for the wireless clients and network to which you want the profile applied.

You can use this procedure if you have created multiple wireless profiles in your wireless network policy and you want to order the profiles for optimal effectiveness and security.

To ensure that wireless clients connect with the highest level of security that they can support, place your most restrictive policies at the top of the list.

This ensures that the clients that support WPA2 will use that method for the connection rather than the less secure WPA. This procedure provides the steps to specify the order in which wireless connection profiles are used to connect domain member wireless clients to wireless networks. In GPME, in the wireless network properties dialog box for the policy that you just configured, click the General tab. You can only apply the following settings for wireless networks that are not configured on the General tab in the Wireless Network Policy Properties page:.

Allow or deny users to view network types ad hoc or infrastructure to which they are denied access. Membership in Domain Admins , or equivalent, is the minimum required to complete these procedures. On the Network Permissions tab, click Add.

The New Permissions Entry dialog box opens. In Network Type , select Infrastructure or Ad hoc. If you are uncertain whether the broadcasting network is an infrastructure or ad hoc network, you can configure two network permission entries, one for each network type.

To deny your domain members access to ad hoc networks, select Prevent connections to ad-hoc networks. To deny your domain members access to infrastructure networks, select Prevent connections to infrastructure networks. To allow your domain members to view network types ad hoc or infrastructure to which they are denied access, select Allow user to view denied networks. To allow users to create profiles that apply to all users, select Allow everyone to create all user profiles. To specify that your users can only connect to allowed networks by using Group Policy profiles, select Only use Group Policy profiles for allowed networks.

Create NPS Policies for You can install NPS on a domain controller or on a dedicated server. The NPS snap-in opens. The Network Policy Server dialog box opens. Client computers, such as wireless portable computers and other computers running client operating systems, are not RADIUS clients.

If this occurs, verify that you have the correct AP name and that the AP is powered on and connected to the network. Retype the shared secret in Confirm shared secret. To automatically generate a shared secret, select the Generate check box, and then click the Generate button. Save the generated shared secret, and then use that value to configure the NAS so that it can communicate with the NPS. You can use this procedure to create the connection request policies and network policies required to deploy either After you run the wizard, the following policies are created:.

Open the NPS snap-in. If it is not already selected, click NPS Local. The text and links below the text change to reflect your selection. On the Select Click Next.

On the Specify Do any of the following:. Modify the settings as required. All additions, modifications, and deletions that you make within the Configure For example, if you use the wizard to remove an If after refreshing Group Policy you continue to receive the error message indicating that a certificate cannot be found for use with the authentication method, the certificate is not being displayed because it does not meet the minimum server certificate requirements as documented in the Core Network Companion Guide: Deploy Server Certificates for If this happens, you must discontinue NPS configuration, revoke the certificate issued to your NPS s , and then follow the instructions to configure a new certificate by using the server certificates deployment guide.

Verify that the value in Issuer is correct for the certificate selected in Certificate issued. To allow users to roam with their wireless computers between access points without requiring them to reauthenticate each time they associate with a new AP, select Enable Fast Reconnect.

Click OK. In Specify User Groups , click Add , and then type the name of the security group that you configured for your wireless clients in the Active Directory Users and Computers snap-in. For example, if you named your wireless security group Wireless Group, type Wireless Group. Your NPS policies are now created, and you can move on to joining wireless computers to the domain. The easiest method to join new wireless computers to the domain is to physically attach the computer to a segment of the wired LAN a segment not controlled by an This is easiest because wireless group policy settings are automatically and immediately applied and, if you have deployed your own PKI, the computer receives the CA certificate and places it in the Trusted Root Certification Authorities certificate store, allowing the wireless client to trust NPSs with server certs issued by your CA.

Likewise, after a new wireless computer is joined to the domain, the preferred method for users to log on to the domain is to perform log on by using a wired connection to the network. To actually create the access point, open the command prompt in the Administrator mode.

To do that on Windows 10, you could press the Win-X keys and select Command prompt Admin from the menu. Then, enter the following two commands into the command prompt:. This creates the access point, but it's not fully operational yet: you need to tell Windows that you want to share your actual Internet connection with the access point you've just created. There, click on the connection that provides the actual connection to the Internet which could be your Wi-Fi connection or the Ethernet line, depending how you have connected to the Internet.

Check the Allow other users to connect through this computer's Internet connection box, and also select Local area connection in the Home networking connection list. This should make your laptop to work as a Wi-Fi access point. Connect to it, as usual, entering the password you have set up, and your device should now be connected to the Internet via the laptop.

Pretty neat, huh? Password-protect and hide personal files and folders with Folder Guard for Windows 11,10,8. User rating: 4. Read more Well, it all should work well in theory. In practice, though, we discovered that not all is smooth. If you connected a device to MyLaptopWiFi , but there is no connection to the Internet on that device, try to restart the laptop, and repeat the steps above again, it may work better the second time. Or, it appears that enabling the access point may not work well with the power transitions of your laptop.

That is, if you try to put the laptop to sleep, it may not work and the laptop may stay awake while the access point is enabled. We also experienced a few blue screen crashes, although not that frequently to make it a real concern. It may depend on the model of your laptop or the Wi-Fi card that your laptop has; some combinations may work better than others. Keep in mind, that if you put your laptop to sleep or restart it, the access point disappears and you would need to set it up again each time you wake up the laptop.

If you do this frequently and don't want to go through the same steps every time, you may want to use Windows Task Scheduler to do it for you. For example, put the two commands shown above in a batch file, and then create a new task that would run that batch file, and set the trigger for that task On workstation unlock.

This way, every time you wake up the laptop and unlock it, the batch file would run for you automatically. When you no longer need it, disable the task in Task Scheduler.